This post contains affiliate links. This means I will make a commission at no extra cost to you should you click through and make a purchase [ “As an Amazon Associate, I earn from qualifying purchases.” ]. Read the full disclosure here.
How to Fix the P0012 Ford F150 Code GuideMechanic.Com When your car displays a P0012 Ford F150 engine trouble code, it’s time to pay close attention.
This engine trouble code means that the camshaft is causing an issue during the engine’s progressing or decelerating phases.
When the problem occurs, warning lights will appear, indicating that a repair is necessary. A problem with the camshaft can result in poor turning or a rough start, and this will cause a warning light to illuminate.
How to Fix the P0012 Ford F150 Code
Possible causes of p0012 code
Check out this MAS Set of 8 Ignition Coils Pack Straight Boot
If you get the P0012 code on your Ford F150, you have probably found out that your engine is over-revving. This causes your car to run poorly, and it also can lead to hard starts.
Other possible causes of the code include a bad intake camshaft position actuator solenoid or an issue with the wiring harness to the sensor. Listed below are some other possible causes of the code on your Ford F150.
If you notice your vehicle drivability is affected, there are several causes of this code. Some of the symptoms include a rattling noise in the engine, a rough idling, and poor acceleration.
While these symptoms may be annoying, they can also damage internal engine components. If you experience any of these symptoms on your Ford F150, it’s important to visit a mechanic immediately to get it checked out before it causes more damage to your vehicle. If you’ve found the code yourself, you can attempt to diagnose it yourself with a scan tool.
A P0012 code on your Ford F150 indicates a problem with the variable valve timing system. The engine’s computer determines that the camshaft position angle is mismatched.
If the problem persists, visit your mechanic as soon as possible. A good OBD-II trouble code scanner can help you identify the exact problem, and you can also use Jerry, the expert assistant for everything car related.
While there are several causes of the P0012 code on a Ford F150, the most common are oil and air filter issues. When the oil is too thick, the engine cannot properly cool and the valve must be replaced.
These problems can result in a check engine light that illuminates. A mechanic can also check the Bank 1 Intake Camshaft Oil Control Valve to determine if it’s causing the trouble.
If you’re not an automotive specialist, this code can be very complicated. It may indicate a malfunctioning camshaft variable timing solenoid or a worn-out timing chain.
Without the proper diagnostic skills, the P0012 code on Ford F150 can be difficult to determine. For this reason, you should contact an expert who can help you properly diagnose the problem.
The good news is that most OBD-II codes share the same causes and symptoms. The problem is that there’s no single fix for them. The solution is dependent on the underlying cause and the vehicle make.
If your car is exhibiting any of the symptoms listed above, it’s important to determine whether it’s a simple camshaft problem.
While it’s possible to fix the code yourself, you should be aware that the repair may require specialized equipment and a thorough diagnosis.
As such, it’s not something for a do-it-yourselfer to attempt. If you are unsure of how to fix a P0012 code, contact a certified Ford F150 repair shop.
Symptoms
Symptoms of P0012 Ford F150 code indicate that your car’s camshaft position angle is misaligned. This code is caused by problems with the camshaft actuators and oil control solenoids that control the valve timing.
This error can also be caused by low oil levels, stretched tensioners, or worn timing chains. If you see any of these symptoms, you should contact a mechanic immediately.
A malfunction in this valve can cause your engine to run rough and cause the p0012 code to appear. This code indicates that you should replace the valve.
The best way to do this is to replace it with a new one. Check the oil level and oil filter to ensure that they are still within the range of the engine’s effective life. If you notice any of these symptoms, you should get your car checked by a mechanic.
Another common problem resulting in the P0012 code is the camshaft timing. The camshafts’ timing is off by about a second, so your vehicle may be stalling or rattling.
You should also notice increased hesitation and poor acceleration. If left unchecked, the error can lead to serious damage to internal engine components. To get your Ford truck running again, consult a mechanic for a diagnostic test.
Luckily, the P0012 Ford F150 code can be easily fixed with the use of a diagnostic tool. This tool communicates with the car’s computer and collects the error messages that it receives.
It displays a code number and, if the scanner is advanced, it will also present proposed solutions. If you don’t see the code on your screen, it is most likely a minor issue and shouldn’t be attempted at home.
The P0012 Ford F150 code is a result of a problem with the camshaft timing. If you suspect that your camshaft is the problem, you should contact a mechanic.
It is not recommended for a DIY repair because it requires specialized equipment. The diagnostic tool will help you identify which components need to be replaced. To make sure that the fault code is the real problem, you should use an OBD II scan tool.
Besides the P0012 code being a sign of a serious engine problem, it is a good idea to take your truck to a mechanic if you see any of these symptoms.
Most mechanics charge $75 to $150 to diagnose the issue and repair it. But you might need to go ahead and spend a few hundred dollars for an oil change if you don’t have the necessary tools or expertise.
P0012 Ford F150 Code
Fix
If your Ford F150 is giving you a trouble code, you need to know how to fix it. This trouble code may indicate that the camshaft angle is mismatched.
While the actual cause of the problem may be different for every Ford model, there are some common symptoms to watch for.
You may experience loud noises when you start the vehicle, decrease in fuel efficiency, and a malfunctioning check engine light. If you notice any of these symptoms, it’s time to visit a mechanic and have it checked out.
Fortunately, the good news is that there are easy fixes available that won’t cost you a fortune. For starters, you should always check the oil and the filter to ensure that they are within their lifespan.
The P0012 trouble code may also be the result of an oil filter failure, a bad intake camshaft position actuator solenoid, or even wiring problems. It is best to take your Ford in for a checkup right away to ensure that your vehicle will keep running smoothly.
To fix P0012 ford f150 code, you can either take your car to a mechanic or try DIY methods. A professional mechanic can diagnose the problem for you, but a simple oil change may do the trick.
Make sure to change the oil filter and use the recommended engine oil. The repair should cost around $50. If you cannot afford the visit to a mechanic, consider taking your vehicle in for an oil change.
In most cases, you’ll need to replace a damaged camshaft. This problem will impact your vehicle’s fuel mileage and performance, as well as your emissions test results.
Additionally, a damaged camshaft may also result in other problems related to the valve train and engine. If the camshaft is causing the P0012 problem, it’s best to leave the repair work to professionals.
You can search online for information on how to repair the problem or consult your owner’s manual. However, if you’re not sure, you can subscribe to ALLDATA’s online car repair service.
Another common reason for this trouble code is a malfunctioning variable valve timing system. The variable valve timing system is what improves the engine’s fuel efficiency.
It controls the camshaft angle through an oil control valve, which is connected to the engine control module. If one of these components is malfunctioning, it can result in a trouble code. In some cases, however, it can be simple to fix the problem yourself.
Before you attempt to repair the P0012 trouble code, make sure to check the oil level in the engine. You might be able to do this by changing the oil, but if the problem persists, you may need to take the car to a mechanic for further inspection.
The check engine light will illuminate again if you don’t fix it yourself. If your car has significant performance issues, you should not drive it until you have fixed the problem.
- P0096 Intake Air Temperature Sensor 2 Circuit Range/Performance Bank 1 - September 7, 2024
- P007e Code Chevy Silverado: Causes, Diagnosis, and Solutions - September 1, 2024
- P007E Code Chevy Cruze: Causes, Diagnosis, and Solutions - August 29, 2024